GT2560 Board ArduinoMEGA+Ultimaker

59,90 € *

inkl. MwSt. zzgl. Versandkosten

Ware am Lager,
Lieferzeit ca. 10-14 Werktage

  • SW10052
ACHTUNG: Das Board ist ab sofort verfügbar. Adapterkabel können gesondert in der... mehr
Produktinformationen "GT2560 Board ArduinoMEGA+Ultimaker"

ACHTUNG: Das Board ist ab sofort verfügbar. Adapterkabel können gesondert in der benötigten Stückzahl bestellt werden. Es passen aber auch vorübergehend die normalen 2,54mm Pfostenbuchsen.

Auf dem GT2560 Board wurden ein Arduino MEGA256 und das Ultimaker-Shield vereinigt.

Das GT2560 ist nicht nur hardware- und softwarekompatibel mit der Kombination aus ArduinoMEGA256 + Ultimaker Boards, sondern es enthält weitere premium Features: Die aufgeräumten Schnittstellen verringern die Störanfälligkeit, die sorgsam ausgewählten, hoch integrierte Bausteine sorgen für einen geringen Platzbedarf der es zusammen mit dem Wegfall der Stapelplatine ermöglicht die Platine leichter und universeller zu befestigen. Sie bietet Platz für 5 universelle, austauschbare POLOLU-Treiberbausteine. Einen Atmega2560 Prozessor mit 256k Speicher, 16Mhz Taktfrequenz und Hochgeschwindigkeits USB-Schnittstelle mit FT232RQ-Baustein. Alle diese Eigenschaften machen das GT2560 zum idealen Kandidaten für 3D-Drucker. Weiterhin kann das GT2560 mit mehr als 12V arbeiten und leistet 90W an dem MOSFET Ausgängen. Das ergibt einen höheren Drehmoment und dadurch eine höhere Schrittrate der Motoren.

Eigenschaften:

  1. Integrierte Funktionen des Arduino MEGA256 mit denen des Ultimaker-Shields. Es berücksichtigt die Hard- und Softwarekompatibilität, ein kompakte Bauform, mehr Anschlussmöglichkeiten und eine höhere Störsicherheit.
  2. Enthält einen ATmega2560 als Prozessor und einen high-performance USB serial Konverter  FT232RQ.
  3. Leistungsteil: Betriebsspannungen von 12-24V. Getrennte Spannungsregelung für die Logikbausteine und Heizbett/Extruderheizung. Der maximale Strom für das Heizbett ist 12A und 5A für die anderen Leistungsteile. Spannungsversorgung für einen 12V Lüfter.
  4. Auf dem Board befinden sich zwei SMD-Sicherungen zum Schutz gegen Überlast. Dioden als Verpolungsschutz und eine selbst rückstellende Überlastsicherung auf der 5V Leitung des USB-Ports.
  5. 3x 12V-Anschlüsse für Lüfter und ein PWM-Ausgang für LED oder andere Beleuchtung.
  6. 3x 55A  MOSFET (mit LED Kontrollanzeige, die Leistung ist nur durch die Platine und den Steckkontakt begrenzt). Alle drei MOSFET sind mit Kühlkörper ausgestattet, um eine gleichmäßige Wärmeabfuhr zu gewährleisten und somit die Betriebsstabilität zu erhöhen.
  7. Steckplätze für 5 Treibermodule (POLOLU-Kompatibel, z.B. A4988, DRV8825,usw.). 3 Kanäle für X/Y/Z und 2x Extruder. Das Microstepping kann je Kanal mit DIP-Schaltern eingestellt werden. Das ist wesentlich einfacher, flacher und zuverlässiger als mit Kodierbrücken.
  8. Eingang für 3 Temperatursensoren (100k Termistor werden empfohlen)
  9. Stiftleisten für ein LCD-Display und SD-Card. Unterstützt LCD2004 und LCD12864 Module. Somit ist ein vom PC unabhängiger Betrieb möglich.
  10. Als Firmware kann Marlin oder andere Ultimaker kompatible Firmware benutzt werden.

Steckverbinder:

Die passenden Stecker für die Schrittmotoren und die Endschalter  nennen sich JST-XH 2- und 4- pol. und haben einen Polabstand von 2,54mm.  Die Stecker für die Lüfter nennen sich JST-PH 3 pol. und haben einen Polabstand von 2,00 mm. Die XH-Typen werden auch in den Ladesteckern für LiPo Modellbau Accus verwendet. Oder auch die Stromversorgungsstecker für die kleinen Laufwerke im PC haben diesen Stecker. Wir werden versuchen so schnell wie möglich hierfür Stecker und Anschlusskabel zu bekommen.

Weiterführende Links zu "GT2560 Board ArduinoMEGA+Ultimaker"
Verfügbare Downloads:
Introduction GT2560 is a compact board that is integrated with the mighty function of the... mehr

Introduction

GT2560 is a compact board that is integrated with the mighty function of the Arduino Mega2560+Ultimaker. The GT2560 can not only take full place the Arduino Mega2560+Ultimaker on respect of both software and hardware, but has more premium features: the streamlined interfaces effectively avoid the unnecessary troubles, well-regulated compaction of components highly integrated saves more space and easier to be mounted on most applications.5 stepper motors, swappable driving modules, mighty ATmega2560 processor with 256k memory, 16MHz operating frequency, high-performance USB serial converter FT232RQ, all these make the GT2560 an ideal option for a 3D printer control board. What’s more, GT2560 can run over 12V and output 90W to a MOSFET, which gives higher torque and higher rotation rate.

Features:
1.Integrated with the mighty function of the Arduino Mega2560+Ultimaker, The GT2560 can not only take full place the Arduino Mega2560+Ultimaker on respect of both software and hardware, but also features compact size, more convenient connection, and more stable.
2. Adopt ATmega2560 as the main control chip, coupled with the high-performance USB serial converter FT232RQ.
3. The power pack: operating voltage is 12V-24V; double power supply design feeds for heatbed and logical part separately. The current is 12A for heatbed and 5A for other parts. The cooling fan can support 12V
4. The main circuit adopts SMD fuse tube, the diode added to the power port can provide reverse protection to the whole circuit, in addition, the 5V USB is USB port protected with 500mA Recoverable fuse.
5.3 12v fan output and one PWM output for LED or other lighting equipment.
6. 3 55Amp MOSFET (with LED indicator, the actual output is restricted by the PCB board and the connector), all 3 MOSFET are equipped with heat sink to ensure sufficient heat dissipation and stable operation.
7. Support 5 A4988 stepper drivers (3 for X/Y/Z axis, and 2 for extruders); the subdivision of stepper motor can be setup by dial switch, eliminating jumper caps, easier to operate.
8. 3 temperature sensor input (100k thermistor is recommended)
9. Extended LCD and SD card interface support both LCD2004 and LCD 12864, with which you can print without your PC.
10. The firmware is the prevalent Marlin, which is known for stability, usability, and high-performance.

Hardware resources:

12V/12A and 12V/5A power supply

1 power port for heatbed and 2 for extruder

5 stepper motor input, (3 for X/Y/Z axis, and 2 for extruders)

Extended LCD & SD card interface

6 endstop input(X-MIN, Y-MIN, Z-MIN, X-MAX ,Y-MAX, Z-MAX)

3 input for thermistor (TEMP1, TEMP2 and TEMP3)

3 input for12V cooling fan

1 PWM output

Dimension: 107.3mm*78.7mm*22mm

Weight: 80 g

Bewertungen lesen, schreiben und diskutieren... mehr
Kundenbewertungen für "GT2560 Board ArduinoMEGA+Ultimaker"
Bewertung schreiben
Bewertungen werden nach Überprüfung freigeschaltet.
Bitte geben Sie die Zeichenfolge in das nachfolgende Textfeld ein.

Die mit einem * markierten Felder sind Pflichtfelder.

DRV8825 Stepper Driver DRV8825 Stepper Driver
Inhalt 1 Stück (0,00 € * / Stück)
9,98 € *
TIPP!
Fräser 3.175 mm VHM-Fräser 1 Schneide Diamantschliff
Inhalt 1 Stück
4,98 € *
Aluwinkel Druckguss 20x20mm Aluwinkel Druckguss 20x20mm
Inhalt 10 Stück (0,80 € * / 1 Stück)
7,98 € *
Blechmutter für Nutenprofil Typ 5 (10St.) Blechmutter für Nutenprofil Typ 5 (10St.)
Inhalt 10 Stück (0,35 € * / 1 Stück)
3,49 € *
TIPP!
StepStick A4988 Treibermodul StepStick A4988 Treibermodul
Inhalt 1 Stück
7,98 € *
Belt Clip Belt Clip, 9 mm Breite
Inhalt 1 Stück
0,89 € *
TIPP!
Bausatz GRBL-NANO-Board GRBL-NANO-Board
Inhalt 1 Paket(e)
ab 20,00 € *
TIPP!
Bestücktes Shield GRBL-Shield v2.00 für POLOLU-Treiber
Inhalt 1 Paket(e)
ab 17,50 € *
TIPP!
TIPP!
POLOLU Stepper Driver TB67S109 POLOLU Stepper Driver TB67S109
Inhalt 1 Stück (0,00 € * / Stück)
11,98 € *
DRV8825 Stepper Driver DRV8825 Stepper Driver
Inhalt 1 Stück (0,00 € * / Stück)
9,98 € *
TIPP!
4T5618S2404-A NEMA 23 Schrittmotor von Nanotec
Inhalt 1 Stück
ab 14,95 € *
Geflechtschlauch, Tyton PET, Ø 8 mm, schwarz Geflechtschlauch, Tyton PET, Ø 8 mm, schwarz
Inhalt 1 Meter (0,00 € * / Meter)
1,50 € *
TIPP!
TIPP!
von Vorme Shapeoko-ONE, Kit´s
ab 299,00 € *
TIPP!
Laufrollen für Makerslide und Openbuild Laufrollen für Makerslide und Openbuild
Inhalt 1 Stück (0,00 € * / Stück)
ab 1,49 € *
GRBL-NANO Experimentier Platinen Set GRBL-NANO Experimentier Platinen Set
Inhalt 3 Stück (3,33 € * / 1 Stück)
9,99 € *
Mini-Fräsmotor Mini-Fräsmotor
39,95 € *
LAPP ÖLFLEX® CLASSIC 100 Steuerleitung 4 x 0.50 mm² Grau LAPP ÖLFLEX® CLASSIC 100 Steuerleitung 4 x 0.50...
Inhalt 1 Meter (0,00 € * / Meter)
1,28 € *
Alu Befestigungswinkel Alu Befestigungswinkel
Inhalt 1 Stück
2,49 € *
ShapeOko2 Kit ShapeOko2 Kit
ab 299,00 € *
TIPP!
C-Beam Profil C-Beam Profil
0,04 € *
Kühlkörper-Set für POLOLU Treiber Kühlkörper-Set für POLOLU Treiber
Inhalt 4 Stück (0,40 € * / 1 Stück)
1,60 € *
TIPP!
Arduino Nano Board Funduino NANO Experimentier Board
Inhalt 1 Paket(e)
5,00 € *
Shapeoko-T, Root-Kit Shapeoko-T, Root-Kit
ab 369,00 € *
Aluwinkel Druckguss 20x20mm Aluwinkel Druckguss 20x20mm
Inhalt 10 Stück (0,80 € * / 1 Stück)
7,98 € *
TIPP!
TIPP!
CameraSlide Set CameraSlide Set
Inhalt 1 Paket(e)
59,90 € *
Schaltnetzteil 24V Schaltnetzteil 24V
ab 39,95 € *
Zuletzt angesehen